Umeå universitets logga

Unlike many methods of chemical modification of Graphite Oxide (GO) reported during 1930-1960 and re-studied in much detail over the last decade, acetylation somehow escaped attention and remained almost completely unexplored. Acetylated Graphite Oxide (AcGO) was prepared using a reaction with acetic anhydride. Successful acetylation is evidenced by an increase in the average interlayer distance fromd(001) = 7.8 angstrom in the precursor GO to 10 angstrom in AcGO. The amount of oxygen in AcGO significantly decreased compared to the precursor GO (C/O = 2.2), reflecting partial reduction of GO in the process of acetylation and resulting in a scarcely functionalized material with C/O = 6.2. A theoretical model of the complete acetylation of GO results in a non-porous close packed molecular structure with an interlayer distance of similar to 10 angstrom, in good agreement with experiment. Remarkably, AcGO shows significant swelling despite the oxidation degree being comparable to that of reduced GO, which does not swell in polar solvents. Moreover, AcGO shows swelling in acetonitrile similar to that of the precursor GO but not in water, thus providing an example of selectivity in the sorption of common polar solvents. The low oxidation degree combined with selective swelling properties makes AcGO a promising material for membrane applications.

Intercalation of dyes into thin multilayered graphene oxide (GO) films was studied by neutron reflectivity and X-ray diffraction. Methylene blue (MB) penetrates the interlayer space of GO in ethanol solution and remains intercalated after the solvent evaporation, as revealed by the expansion of the interlayer lattice and change in chemical composition. The sorption of MB by thin GO films is found to be significantly stronger compared to the sorption of Crystal violet (CV) and Rose bengal (RB). This effect is attributed to the difference in the geometrical shape of planar MB and essentially nonflat CV and RB molecules. Graphite oxides and restacked GO films are found to exhibit different methylene blue (MB) sorptions. MB sorption by precursor graphite oxide and thin spin-coated films of GO is significantly stronger compared to freestanding micrometer-thick membranes prepared by vacuum filtration. Nevertheless, the sorption capacity of GO membranes is sufficient to remove a significant part of the MB from diluted solutions tested for permeation in several earlier studies. High sorption capacity results in strong modification of the GO structure, which is likely to affect permeation properties of GO membranes. Therefore, MB is not suitable for testing size exclusion effects in the permeation of GO membranes. It is not only hydration or solvation diameter but also the exact geometrical shape of molecules that needs to be taken into account considering size effects for penetration of molecules between GO layers in membrane applications.

Intercalation of very long molecules into the structure of multi-layered graphene oxide (GO) was studied using example of 1-hexadecanol (C16), an alcohol molecule with 16 carbon atoms. Brodie graphite oxide (BGO) immersed in excess of liquid C16 just above the melting point shows expansion of c-unit cell parameter from ∼6 Å to ∼48.76 Å forming a structure with two densely packed layers of C16 molecules in a perpendicular orientation relative to the GO planes (α-phase). Heating of the BGO-C16 α-phase in excess of C16 melt results in reversible phase transition into β-phase at 336–342K. The β-phase shows much smaller unit cell parameter of 29.83 Å (363K). Analysis of data obtained using vacuum-driven evaporation of C16 from the β-phase provides evidence for structure of β-phase consisting of five layers of C16 molecules in parallel to GO plane orientation. Therefore, the transition from α-to β-phase corresponds to change in orientation C16 molecules from perpendicular to parallel relative to GO planes and decrease in the amount of intercalated solvent. Cooling of the β-phase in absence of C16 melt is found to result in the formation of γ-phase with inter-layer distance of ∼26.5 Å corresponding to one layer of C16 molecules intercalated perpendicularly relative to the GO planes. Structures with one and two layers of C16 molecules parallel to GO planes were identified in samples with rather small initial loading of C16. Surprisingly rich variety of structures revealed in the BGO-C16 system provides opportunities to create materials with precisely controlled GO inter-layer distance.

Swelling is the most fundamental property of graphite oxides (GO). Here, a structural study of Brodie graphite oxide (BGO) swelling in a set of long chain 1-alcohols (named C11 to C22 according to the number of carbons) performed using synchrotron radiation X-ray diffraction at elevated temperatures is reported. Even the longest of tested alcohols (C22) is found to intercalate BGO with enormous expansion of the interlayer distance from ≈6Å up to ≈63Å, the highest expansion of GO lattice ever reported. Swelling transitions from low temperature α-phase to high temperature β-phase are found for BGO in all alcohols in the C11–C22 set. The transitions correspond to decrease of inter-layer distance correlating with the length of alcohol molecules, and change in their orientation from perpendicular to GO planes to layered parallel to GO (Type II transitions). These transitions are very different compared to BGO swelling transitions (Type I) found in smaller alcohols and related to insertion/de-insertion of additional layer of alcohol parallel to GO. Analysis of general trends in the whole set of 1-alcohols (C1 to C22) shows that the 1-alcohol chain length defines the type of swelling transition with Type I found for alcohols with C<10 and Type II for C>10. 

Graphene oxide (GO) pillared with tetrakis(4-aminophenyl)methane (TKAM) molecules shows a narrow distribution of pore size, relatively high specific surface area, but it is hydrophilic and electrically not conductive. Analysis of XRD, N₂ sorption, XPS, TGA and FTIR data proved that the pillared structure and relatively high surface area (∼350 m² g⁻¹) are preserved even after thermal reduction of GO pillared with TKAM molecules. Unlike many other organic pillaring molecules, TKAM is stable at temperatures above the point of GO thermal reduction, as demonstrated by TGA. Therefore, gentle annealing results in the formation of reduced graphene oxide (rGO) pillared with TKAM molecules. The TKAM pillared reduced graphene oxide (PrGO/TKAM) is less hydrophilic as found using dynamic vapor sorption (DVS) and more electrically conductive compared to pillared GO, but preserves an increased interlayer-distance of about 12 Å (compared to ∼7.5 Å in pristine GO). Thus we provide one of the first examples of porous rGO pillared with organic molecules and well-defined size of hydrophobic slit pores. Analysis of pore size distribution using nitrogen sorption isotherms demonstrates a single peak for pore size of ∼7 Å, which makes PrGO/TKAM rather promising for membrane and molecular sieve applications.

High-surface area activated graphene has a three-dimensional porous structure that makes it difficult to prepare dispersions. Here we report a general approach that allows the preparation of stable water-based dispersions/inks at concentrations of ≲20 mg/mL based on activated graphene using environmentally friendly formulations. Simple drying of the dispersion on the substrate allows the preparation of electrodes that maintain the high specific surface area of the precursor material (∼1700 m²/g). The electrodes are flexible because of the structure that consists of micrometer-sized activated graphene grains interconnected by carbon nanotubes (CNTs). The electrodes prepared using activated graphene demonstrate performance superior to that of reduced graphene oxide in supercapacitors with KOH and TEA BF₄/acetonitrile electrolytes providing specific capacitance values of 180 and 137 F/g, respectively, at a specific current of 1 A/g. The high surface area of activated graphene in combination with the good conductivity of CNTs allows an energy density of 35.6 Wh/kg and a power density of 42.2 kW/kg to be achieved. The activated graphene dispersions were prepared in liter amounts and are compatible with most industrial deposition methods.

A spray gun machine was used to deposit high‐surface‐area supercapacitor electrodes using green non‐toxic aqueous dispersions based on different kinds of high specific surface area nanostructured carbon materials: activated graphene (a‐rGO) and activated carbon (AC). Tuning the spray conditions and dispersion formulation allowed us to achieve good adhesion to stainless‐steel current collectors in combination with high surface area and a satisfactory mechanical stability of the electrodes. The specific surface area of approximately 2000 m²/g was measured directly on a‐rGO and AC electrodes showing only around a 20 % decrease compared to the precursor powder materials. The performance of the electrodes deposited on stainless‐steel and aluminum current collectors was tested in supercapacitor devices using three electrolytes. The electrodes were tested in an “as‐deposited” state and after post‐deposition annealing at 200 °C. The spray deposition method and post‐deposition annealing are completely compatible with roll‐to‐roll industrial production methods. The a‐rGO demonstrated superior performance compared to AC in supercapacitor electrodes with gravimetric capacitance, energy, and power density parameters, which exceed commercially available analogues. The formulation of the dispersions used in this study is environmentally friendly, as it is based on only on water as a solvent and commercially available non‐toxic additives (graphene oxide, fumed silica, and carbon nanotubes).

High surface area carbons are so far the best materials for industrial manufacturing of supercapacitor electrodes. Here we demonstrate that pine cones, an abundant bio-precursor currently considered as a waste in the wood industry, can be used to prepare activated carbons with a BET surface area exceeding 3000 m2 g−1. It is found that the same KOH activation procedure applied to reduced graphene oxide (rGO) and pine cone derived biochars results in carbon materials with a similar surface area, pore size distribution and performance in supercapacitor (SC) electrodes. It can be argued that “activated graphene” and activated carbon are essentially the same kind of material with a porous 3D structure. It is demonstrated that the pine cone derived activated carbon (PC-AC) can be used as a main part of aqueous dispersions stabilized by graphene oxide for spray deposition of electrodes. The PC-AC based electrodes prepared using a semi-industrial spray gun machine and laboratory scale blade deposition of these dispersions were compared to pellet electrodes.